Ladder Cable Type
Cable Tray – Ladder Type are ideal to install large volume of Heavy duty power cables. Perforation make full free air rating of cable ,Higher current flow can be achieved at the same cross section , Over heating and consecutive damaging of cable is avoided ,coupler holes in side guarantees easy connecting of cable trays to each other ,Cable trays can be manufactured in Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height of cable trays is varies from 25,35,50,70,75,100 & 125 mm , Wdth of cable trays is varies from 100 to 1000 mm ,Thickness of cable trays ranging from 10,12,14,16,18 SWG, i.e 3,2.5,2,1.6,1.2 mm
‘ T ’ Bend – Ladder Type, Is Suitable For Joining Cable Trays In Three Directions At 90 Degree Intervals In The Same Plane. Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out , Peel Off Or Get Damage While Laying Of Cables.
‘ T ’ Bend – Ladder Type , Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of ‘ T ’ Bend – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm , Width Of ‘ T ’ Bend – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness Of ‘ T ’ Bend – Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
Cross Bend – Ladder Type Are Mainly Use For Laying The Cable Horizontally Which Allows The Cable To Route From Four End , Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out , Peel Off Or Get Damage While Laying Of Cables.
Cross Bend – Ladder Type , Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of Cross Bend – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm , Width Of Cross Bend – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness Of Cross Bend – Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
Horizonal Bend (Elbow) – Ladder Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable In 90 Degree Where Two Wall Are Conjoining With Constrain Of Vertical Pillar Or Obstacle To It , , Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out , Peel Off Or Get Damage While Laying Of Cables.
Horizonal Bend (Elbow) – Ladder Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of Horizonal Bend (Elbow) – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm , Width Of Horizonal Bend (Elbow) – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness Of Horizonal Bend (Elbow) – Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
Vertical Bend Outside – Ladder Type Are Mainly Use In Combination With Perforated Type Of Cable Trays To Route The Cable Where The The Direction Changes To A Different Plane.
Vertical Bend Outside – Ladder Type Changes Direction Downward From The Horizontal Plane. Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out, Peel Off Or Get Damage While Laying Of Cable.
Vertical Bend Outside – Ladder Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of Vertical Bend Outside – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm , Width Of Vertical Bend Outside – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness Of Vertical Bend Outside – Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
Vertical Bend Inside – Ladder Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable Where The The Direction Changes To A Different Plane.
Vertical Bend Inside – Ladder Type Changes Direction Upward From The Horizontal Plane .Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out , Peel Off Or Get Damage While Laying Of Cable.
Vertical Bend Inside – Ladder Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of Vertical Bend Inside – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm , Width Of Vertical Bend Inside – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness of Vertical Bend Inside – Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
Reducer Central – Ladder Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable Where Cable Tray Is Suitable For Joining Cable Trays Of Different Widths In The Same Plane. Reducer Central – Ladder Type Has Two Symmetrical Offset Sides .
Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out,Peel Off Or Get Damage While Laying Of Cable.
Reducer Central – Ladder Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of Reducer Central – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm , Width Of Reducer Central – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness Of Reducer Central – Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
Reducer Left Hand-Ladder Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable Which Is Suitable For Joining Cable Trays Of Different Widths In The Same Plane.A Reducer Left Hand-Ladder Type, When Viewed From The Large End, Has A Straight Side On The Left.
Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out,Peel Off Or Get Damage While Laying Of Cable.
Reducer Left Hand – Ladder Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of Reducer Left Hand – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm ,Width Of Reducer Left Hand – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness Of Reducer Left Hand-Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
Reducer Right Hand – Ladder Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable Which Is Suitable For Joining Cable Trays Of Different Widths In The Same Plane. A Reducer Right Hand – Ladder Type, When Viewed From The Large End, Has A Straight Side On The Left.
Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out,Peel Off Or Get Damage While Laying Of Cable.
Reducer Right Hand – Ladder Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316 , 304 & In Aluminium-Commercial Grade Finish.
Height Of Reducer Right Hand – Ladder Type Is Varies From 25,35,50,70,75,100 & 125 Mm ,Width Of Reducer Right Hand – Ladder Type Is Varies From 100 To 1000 Mm ,Thickness Of Reducer Right Hand – Ladder Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm
